Summer Starts Here - Save up to 70%
Trailer Wiring Harness Installation - 2013 Chrylser 300- Video
Today on our 2013 Chrysler 300 we will be installing the Curt T-Connector Vehicle Wiring Harness with 4 Pole Flat Trailer Connector, part number C56145. When we want to use the wiring we'll just take some out of the trunk like so so we can make our connection to the trailer. Make sure we avoid the latch here and close the trunk on over it. This will keep it secure and it'll be easy to use. When you're done towing your trailer you open the trunk back up, lift up on the spare tire cover panel and store your wires just like so and have full access to your trunk; you don't have to worry about snagging the wire on anything. Here's what comes in our wiring harness package. We have our control module here, which will prevent any voltage being back fed into the vehicle's wiring harness. more
6/20/2016 3:55:22 PM
Trailer Wiring Harness Installation - 2015 Chrysler Town and Country- Video
Today on our 2015 Chrysler Town and Country, we're going to take a look at and show you how to install the tow ready T1 vehicle wiring harness with the 4 pole flat trailer connector. The part number is 118534. Now here's what the wiring harness is going to look like before we start installing it. We've got the center of the operation, which is the ModuLite. This is a module. Hooks into the battery of the vehicle using the 12 volt power chord that's provided. Also goes through a fuse holder. more
7/14/2015 11:57:32 AM
Trailer Wiring Harness Installation - 2012 Chrylser 300C- Video
Today on our 2012 Chrysler 300C, we're going to review and install the Curt T-Connector Custom Fit Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part number C56145. Now with the Curt Custom Fit Vehicle Wiring Harness with 4-Pole Flat Trailer Connector already installed, let's go ahead and take a look at it. The 4-pole connector is going to store down with the spare tire. By storing it inside, it keeps it out of the inclement weather and prevents buildup of rust and corrosion over time. To use it, we'll simply take it out of the spare tire well and run it out over the threshold. Stay away from the latch, because pinching it off in the latch will damage the wire. However, the weather stripping is thick enough that we can simply close the rear trunk on it. Pull out the wire we need to run to our hitch or accessory, and then when we're done simply roll it up and store it back inside. more
6/10/2015 8:53:07 AM
Trailer Wiring Harness Installation - 2012 Chrysler Town and Country- Video
All right, today on this 2012 Chrysler Town & Country, we're going to show you the CURT key-connector vehicle wiring harness with a four-pull flat trailer connector, part number C56150. These are the parts that you get with the kit, a T-connector right here. This one with the yellow wire goes to the left-hand side or the driver's side, and we have a T-connector here that goes up to the right-hand side. These connections are made right behind the tail light. These two wires go down to the module here and when signal goes to the module here, it goes out to our four-pole flat. Also, our four-pole flat comes with a protective cover when you are not using it. Now our module is going to need to get power from a 12-volt power supply up-front. more
5/26/2015 3:22:09 PM
Trailer Wiring Harness Installation - 2010 Chrysler 300- Video
Today on our 2010 Chrysler 300 we're going to be installing the tow ready T1 vehicle harness with the four pull flat trailer connector its part number is 118406. Now when ready for use we'll just pull our four pull wire out, bring our cover down and over. Now when your using it pull out whatever length you need to make your connection and we'll let it rest right over the gasket. We want to avoid the latch section there, but then when you close it your gaskets going to hold that in place and give you a nice pig tail out here where you can use it. The cover over the top here can come in pretty handy, for getting this kind of tucked away we can use this as almost like a buckle or a strap for it. Get it all squeezed together real close and bring that around like that. Kind of keep it bundled up there nice little tuck in area there you wouldn't even have to tuck it in underneath. more
5/22/2015 7:57:52 AM
Trailer Wiring Harness Installation - 2014 Chrysler Town and Country- Video
Today in a 2014 Chrysler Town & Country, we're going to show you a T1 vehicle wiring harness with 4-pole flat trailer connector from Tow Ready, part number 118534. We've got our parts laid out from the box, so we'll do a little bit of show and tell. First off, what color are the lower components and the ends The T-connector with the yellow wire here, goes to a connection point that's located behind driver side tail light. The T-connector with the green wire, goes over to the same connection over on the passenger side. We have a white wire with a ring terminal. That goes through sheet metal for ground. Now this black wire here, gets connected to a 12 volt power supply, so it powers our module which copies a signal that comes from our other 2 connection points. more
4/28/2015 12:47:15 PM
Trailer Wiring Harness Installation - 2015 Chrysler Town and Country C56150- Video
Today on this 2015 Chrysler Town and Country we're going to show you the Curt T-Connector Vehicle Wiring Harness, part number C56150. We'll go ahead and show you the components that come with this part number. First off this is our wire harness here. This is our four-pole flat. This is our module right here. That takes our battery power, copies the signal and sends it out to the trailer. We have our T-connector, we're yellow for the left hand side and our T-connector with the green wire for right hand side. We have a length of wire that comes with the kit to run from our module up to the front towards the battery. Once we get to the battery our fuse holder and some zip ties and some butt connectors and ring terminal to our connections up to our battery. more
4/20/2015 1:26:35 PM
Trailer Wiring Harness Installation - 2008 Chrysler Aspen- Video
Today on this 2008 Chrysler Aspen, we're going to install part number c55597 from Curt. This is the Curt T connecter Wiring Harness. First thing we need to do is go ahead and open up the back hatch and get access behind the tail lights. There are two plastic rivets on each tail light that we have to remove so we can take off the tail light. We pull off the center with a pair of pliers, and they come right out. Then set the fasteners off to the side and we'll go ahead and pop the tail light loose. Next we need to disconnect the wire harness. more
1/20/2015 2:47:42 PM
Trailer Wiring Harness Installation - 2012 Chrysler 200- Video
Today on our 2012 Chrysler 200 we're going to be installing the Curt T-Connector Vehicle Wiring Harness with a 4-Pole Flat Trailer Connector, Part Number C56211. We'll first begin our installation by opening up the rear trunk of the vehicle. Next we're going to need to remove a few interior pieces so that we can gain access to the wiring. Since this vehicle is a convertible it is a little bit different than the sedan model. Now with our trunk linings removed, next we're going to need to remove a few other interior pieces. We'll need to remove this rear threshold piece as well as peel back the 2 plastic linings on both sides. To remove the rear threshold piece we'll simply pull up gently so that it unsnaps from its clips. more
12/19/2014 8:41:56 PM
Trailer Wiring Harness Installation - 2008 Chrysler Sebring- Video
Today on our 2008 Chrysler Sebring we will be installing the Tow Ready T-One Connector, part number 118444. To begin with you'll need to raise the trunk lid up. Next you will need to locate the two plastic nuts that are on the backside of each of the light assemblies. On this particular vehicle, since it's a convertible, we we're able to just slip our hand in behind the inner lining of the trunk and get both of the nuts removed from the rear of the light assembly. You'll need to repeat this procedure for both the driver and the passenger side. Once you have the two plastic nuts removed from the rear of the light assembly you'll gently pull the light assembly out, being sure not to break the clip off that slides into the body. Once that is out we will need to disconnect the two wire connections on the back. more
12/10/2014 8:33:46 PM
Trailer Wiring Harness Installation - 2009 Chrysler 300- Video
Today on our 2009 Chrysler 300 we'll be installing the Tow Ready T1 Vehicle wiring harness with four-pole flat trailer connector, part number 118406. To begin with, we'll go ahead and open up the trunk. Both on the driver and the passenger side, there's a small plastic wing nut that'll need to be removed and the carpet pulled back to gain access to the wiring connections. Now that we have both of these removed and the carpet pulled back some, we'll go ahead and start on the passenger side. Before we can remove the factory wiring connection, we need to pull the red tab, which is the locking tab, to the open position on the connection. With that done, we'll go ahead and squeeze the small tab and pull the connector apart. We'll open up the center section of the trunk, or lift it up, exposing the spare tire, as well as the battery. Next we'll go ahead and connect our T1 connector in-line, matching up the male and female opposite ends so that you put the T1 connection in-line for the factory harness. more
11/24/2014 4:22:04 PM
Trailer Wiring Harness Installation - 2003 Chrysler PT Cruiser- Video
Today our 2003 Chrysler PT Cruiser we'll be installing the Curt T-Connector Wiring Kit, part number C55532. To begin with we'll need to remove both tail light assemblies by removing the torxhead screw that's at the lower section on the tail light assembly. Once you pull the tail light assembly out, because careful not to break the clips off as you're removing the tail light assembly. Then we will go ahead and unplug both plugs from the rear of the assembly. On this case we used a small screw driver to help release both of the locking tabs. Once we have the passenger side light assembly out and the wires disconnected we will go ahead and drop down the 4-flat as well as the yellow wire with the connectors down through the light assembly and under the rear bumper fascia. We'll plug the grey connector that has two wires into it with the green wire into the vehicle's harness, making sure that the locking tabs snap into place. We will also make the connection with the plug that has three wires, one of them has a brown and red wire in it as well. more
11/10/2014 10:45:27 AM
Trailer Wiring Harness Installation - 2005 Chrysler 300- Video
Today on our 2005 Chrysler 300 we'll be installing the Tow Ready T-One Connector, part number 118404. We'll go ahead and show you how to use the new 4-pole connector. Well simply take the 4-pole and run it out and down to the hitch or accessory, being careful to stay away from the ledge as pinching the wire off in the ledge can harm the wire. However, the weather stripping is thick enough that it won't and we'll simply close the rear cargo door on it. Once we're finished using our new 4-pole connector, we'll roll it up and store it under the spare tire cover. To install our new 4-pole connector, we'll simply open up the rear cargo door or trunk. We'll need to access the wiring behind the driver and passenger side tail lights. Here on the passenger side we'll go ahead and remove the plastic wing nut and pull back the carpeting to gain access. more
10/27/2014 2:44:19 PM
Trailer Wiring Harness Installation - 2010 Chrysler Town and Country- Video
Today on our 2010 Chrysler Town and Country, we'll be installing the Tow Ready T-One wiring harness with 4-pole flat trailer connector, part number 118552. To begin with, we'll need to go ahead and raise the rear hatch of the vehicle as this is how you access the two screws that hold in each of the taillight assemblies for both the driver and passenger side. To remove the taillight assembly, you'll need a T30 Torx head bit. We'll go ahead and remove the two screws and then you'll need to kind of work the light assembly around a little bit as there are two more tabs up towards the front of the vehicle that need to be pulled out their housing as well. With the taillight assembly removed, we can go ahead and disconnect the wiring harness. To do this, you'll need to release the red locking tabs on each of the two connectors and squeeze the tab and gently pull the plug off of the connector. Now, we're only going to be tying into the top connector, but to make things a little easier, we're going to go ahead and remove the bottom plug as well just so we can go ahead and set our light assembly aside. We'll go ahead and repeat the same process for both the driver and the passenger side. Now, we'll go ahead and take our T-One wiring harness. more
10/6/2014 1:12:54 PM
Trailer Wiring Harness Installation - 2014 Chrysler Town and Country C56150- Video
Today on our 2014 Chrysler Town and Country, we'll be installing the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part number C56150. To begin our install, first we'll open up the rear hatch and locate the fasteners that secure the rear taillight assemblies. We'll remove the fasteners and then remove the taillights. To remove the taillights, we'll simply pull them out towards the rear of the vehicle, releasing the fastener alignment pins underneath. Then to remove the taillight assembly, push up on the read locking tab to release it then press on the connector lock that remove the wiring harness from the socket. We'll set the taillight aside, move over the passenger side and repeat the same process. Now with both taillight assemblies removed, we'll go and take the new wiring harness and the yellow and brown wire connector, plug it in to the manufacturer's wiring on the driver's side. Next we'll take the 4-pole connector and green wire connector and feed it down between the bumper cover and via the vehicle. This will come out down underneath the vehicle where we can then go ahead route the green wire connector over to the passenger side and the 4-pole connector towards the center of the vehicle and ultimately to the hitch. more
9/2/2014 2:52:29 PM
Trailer Wiring Harness Installation - 2007 Chrysler Aspen- Video
Today on this 2007 Chrysler Aspen we are going to install part number 118390 from Tow Ready. First thing we need to do is go ahead and get our vehicle ready to install the wire harness. To do that we need to go ahead and open up the tail gate and get access to remove the tail lights. To remove the tail lights, well go ahead and remove these plastic fasteners with a pair of pliers grip the centres and pull it out. Now were going to remove the tail light. Well go ahead and work the bottom and top little bit and pull back. Theyll unsnap from these fasteners here. Now before we connect the wire harness, weve got to loosen up this red lock right here. more
6/17/2014 8:49:12 AM
Trailer Wiring Harness Installation - 2013 Chrysler Town and Country- Video
All right. Today on our 2013 Chrysler Town and Country, we're going to install part number C56150 from Curt. This is Curt T connector wiring harness with a 4-pole flack. First thing we need to do is get the van ready to install our wire harness. We'll go ahead and open up the back hatch and remove the tail lights. We'll need a ten millimeter socket to remove the lights. more
5/27/2014 4:08:48 PM
TowReady Taillight Converter Hardwire Kit Installation - 2001 Chrysler Sebring- Video
Today in our 2001 Chrysler Sebring convertible, we will be installing the tow-ready, upgraded circuit-protector tail light converter hardware kit with four-pole end, including a tester, part number119178KIT.To begin with here, we're going to figure out whether we have a two-wire or three-wire system on this vehicle. We'll go ahead and run through the light functions and see which bulbs come on when we turn the running lights on, the blinkers, as well as the brake lights. As you can see here with the running lights on, we get the top two bulbs, which are red here, come on on both sides. When you step on the brakes, just the two inner bulbs towards the center of the trunk come on. When we turn each blinker on, it's actually a bulb down below that's part of the clear section. With running this simple test, this tells us that we have a three wire system, so we will be using the red wire on the converter box. We will be connecting this red wire to the brake light wire. Now, let's go ahead and open up the trunk, and we'll go ahead and figure out which wires do which on the back side. We'll begin here on the driver's side. We'll go ahead and just simply peel back the inner lining of the trunk and it will expose the back of the tail light assembly, where we'll simply slide the red locking tab over and unplug the wiring harness from the back of the light assembly. more
11/5/2013 3:38:54 AM
Trailer Wiring Harness Installation - 2008 Chrysler Pacifica- Video
Today on our 2008 Chrysler Pacifica we'll be installing the Tow-ready T-One Vehicle Wiring Harness with 4-Pole Flat Connector, part number 118303.To begin our install, we'll first need to remove the rear taillights. To do this, we'll open up the rear hatch and then remove the 2 screws securing the taillight assembly. Starting on the driver's side, after we remove the screws, we'll set them aside. Using a plastic pry tool or flat-blade screwdriver, gently pry out between the housing and taillight assembly, pulling straight back from the vehicle, to release the fastener underneath, careful not to break this fastener.Next we'll remove the taillightcompletely by unlocking the red locking tab and then pressing on the connector lock, releasing the wiring harness from the taillight assembly. Now that we've removed the driver's side taillight assembly, we'll go ahead and repeat the same process on the passenger side. We'll remove the manufacturer's grommet, where the wiring runs into the body of the vehicle. After we remove the grommet from its position, take the yellow wire, pull it out along with the connector that's wrapped in the foam padding. more
10/22/2013 12:13:50 PM
Trailer Wiring Harness Installation - 2013 Chrysler Town and Country 118534- Video
Today on this 2013 Chrysler Town and Country, were going to install part number 118534. To start off our install were going to open up the back hatch and were going to remove the two taillights. Our two screws that we have to remove and then well pop them loose on the body and then well go ahead and remove the wire harness from the taillight. Theres a small red lock we have to push to unlock it and then a tab that we have to push to release it from the taillight and we can pull it apart. Well set our driver side taillight to the side and do the same thing on the passenger side.Now we can go ahead and start installing the wire harness. First off well take the four pole end and well route it between the body work and the bumper cover going down to the bottom. more
2/8/2013 2:52:29 PM
Trailer Wiring Harness Installation - 2012 Chrysler Town and Country 118534- Video
Today on our 2012 Chrysler Town & Country well be installing the Tow Ready T1 Connector, part number 118534. Now to begin our installation were going to open the rear tailgate to access the screws that hold the taillights in place. Well remove the bolts holding the taillights and carefully pry the taillight housing rearward away from the vehicle being very careful not to break the alignment tabs. Once weve removed the taillights from the vehicle we can pull the red tab here on the connector. Well then push the button and allow the connector to separate. Now here on the drivers side well take the T connector in with the yellow wire and connect it to the vehicle wiring and lock it into place. more
11/19/2012 3:17:50 PM
Trailer Wiring Harness Installation - 2009 Chrysler Town and Country- Video
Today on our 2009 Chrysler Town and Country well be installing the tow ready T1 connector, part number 118552. To start our install well first open up the rear cargo door and remove the driver side tail light housing. There are two fasteners securing the housing that we will remove first. Then well gently pry and pull the tail light assembly away from the body of the vehicle. Be careful not to break the alignment tabs as you do so. Now with our tail light assembly removed we can go ahead and unlock the red locking tab and disconnect the wiring connector from the bulb and socket. more
10/5/2012 1:17:56 PM
Trailer Wiring Harness Installation - 2001 Chrysler Town and Country- Video
Today on our 2001 Chryslser Town and Country, we'll be installing a Tow-ready T-One connector part number 118376. First, we'll go ahead and open up the rear cargo door. Then, we'll need to remove the rear threshold and pull back the paneling on the driver's side. After we complete that, we'll go ahead and remove the two fasteners and secure the driver's side tail light assembly. Once we remove the driver's side tail assembly, we can go ahead and disconnect the manufacturer's wiring to the tail light's assembly. Now, we'll need to go ahead and take the matching end of our Tow-ready connector and feed it in behind the driver's side tail assembly. more
9/7/2012 12:28:27 PM
Trailer Wiring Harness Installation - 2011 Chrysler Town and Country- Video
Today, on this 2011 Chrysler Town and Country, well be installing a Wiring Harness, part number 118534 from Tow Ready. Our first step will be to remove the tail lights. To do this, well be removing these two screws here on both sides of the vehicle. Well then gently rock it back and forth until it comes loose. Youll see the factory plug here, which well remove from the tail light. Push up on this red tab here to unlock it then push down on the black tab and simply pull them apart. more
7/13/2012 1:59:14 PM
Trailer Wiring Harness Installation - 2006 Chrysler Pacifica- Video
Today on our 2006 Chrysler Pacifica, were gonna install the Tow-Ready T1 Connector part number 118303. Our first step is to open up the rear cargo door. Next well need to remove both the rear taillight assemblies. Theres two fasteners for each. As we remove the taillight assembly, well need to gently pry it away from the body of the vehicle. As you can see here, theres a fastener underneath and be careful not to break it off. more
4/26/2012 11:20:10 AM
Trailer Wiring Harness Installation - 2004 Chrysler PT Cruiser- Video
Today on a 2004 Chrysler PT Cruiser, we're going to install product number 118462 from Tow Ready. First thing we need to do is go ahead and remove the tail lights. We're going to remove the wire harness from the tail light we're pushing on the sides of these little tabs right here. Sometimes its easier to push it with a screwdriver. We're going to start off by running a 4-pole wire and our T-connector half with a yellow wire down to the bottom of the tail light and out at the bottom of the bumper. Next, we'll go ahead and remove, attach our ground wire to the body which connects this to a sheet metal around the side here which we'll attach to that. more
1/11/2012 3:21:17 PM
Trailer Wiring Harness Installation - 2002 Chrysler Town and Country- Video
Today we're working on a 2002 Chrysler Town & Country. We're going to install a Tow Ready T1 Connector, product number 118376. Our first step is going to be accessing the rear cargo area of the vehicle and we're going to remove the tail light lens on the driver's side. Here are the two attachment points that we'll need to remove in order to pull the tail light lens off. As you can see, you get underneath the grommet tab and gently pry it out, then we can remove it from holding the tail light lens, one more attachment point that you'll need to be aware of. Gently pry and pull the lens away from the vehicle. more
12/19/2011 4:16:18 PM
Trailer Wiring Harness Installation - 2005 Chrysler Pacifica- Video
Today on this 2005 Chrysler Pacifica, we're going to be installing wiring harness part 118303. Wer'e going to first go ahead and locate the ports that were going to be plugging our wiring harness into. Now these ports are located directly behind the tail lights on both sides of the vehicle, so we're going to go ahead and remove each one of the tail lights. To do that you can see we have opened up our cargo door here to access the fasteners here on the inboard side, just go ahead and remove those and we can pop the tail light right off. If you turn the tail light over here, right here at the bottom is the connector we're going to be using, you want to go ahead and separate the two pieces first. To do that we want to go ahead and slide the red locking tab over first and then go ahead and press the release button here at the top and pull the two pieces apart. We can set the tail light off to the side for the time being and go ahead and do that for the passenger side as well. We are going to continue over here on the drivers side, and pull the grommet away from the vehicle. This wiring harness is actually a powered unit and when we pull the grommet away we actually have an existing power wire that were going to use. If you follow the tape forward here you can see there is a red wire here that is taped off and if you cut that back, there is a connector on there and we're going to go ahead and use that. more
12/7/2011 2:28:48 PM
Trailer Wiring Harness Installation- 2005 Chrysler Pacifica- Video
Today on this 2005 Chrysler Pacifica we are going to install Tow Ready T-One connector part number 118303. First, we are going to open the tailgate so we can access the mounting bolts for the drivers side tail light lens. We are going to remove these two mounting bolts here. Now that we have the two mounting screws removed we are going to remove the tail light assembly. Be careful not to break the alignment tabs that are still connected. As you can see here, it gives us access to the rear tail light wiring. Now that we have the lens assembly away from the vehicle, we need to locate this red wire connector which will be attached to the manufacturers wiring harness. We are going to pull it up and out of the vehicle and connect our new Tow Ready T-One harness to it. Then, we will slide the locking tab into place. 1:02 more
7/29/2011 9:34:58 AM
Trailer Wiring Harness Installation - 2008 Chrysler Town and Country- Video
Today on this 2008 Chrysler Town and Country we will be installing part number 118552 from Tow Ready. The first step involved is to open the rear hatch so we can remove the tail lights and get to our connections. We have to remove these two screws here and here. With the driver side done, we will repeat this process on the passenger side. When pulling the lights, gently rock them back and fourth to loosen up the push pins, then pull out. :28 more
6/9/2011 9:49:33 AM
Trailer Wiring Harness Installation - 2009 Chrysler Aspen- Video
Today on this 2009 Chrysler Aspen we are going to install part number 118390 from Tow Ready. This is their modulite wiring harness. The first thing we need to do is open up the back hatch of the vehicle and get to the fasteners that hold the lights in place. We are going to remove the taillights as our first step. These just have plastic fasteners that you just remove. When you pull these off, you want to kind of pull them off to the side a little bit and pull back a little bit. We can go ahead and disconnect this light for now. Just push in this red tab right here and push down this button and it comes apart. We have our driver side off. Let us go ahead and do the same thing with the passenger side. Next we are going to take our wire harness and we are going to the 4-pole end down behind the bumper, towards the ground for now. And then the lead with the red, yellow and brown wires, we are going to hook up to the wiring harness that was going into the taillight. Next we will take our white and green wire and do the same thing like we did with the 4-pole wire. Drop it behind the bumper and out of our way. 1:01 more
3/14/2011 6:19:42 AM
Trailer Wiring Harness Installation - 2004 Chrysler Town and Country- Video
Today on this 2004 Chrysler Town and Country we are going to be installing wiring harness part number 118300. We are in the rear cargo area of the Town and Country and we are going to locate the ports that we are going to be plugging the wiring harnesses into. The ports for the harness are located directly behind the tail lights on both the driver and passenger sides of the vehicle. However the harness itself is going to be routed and stored inside the vehicle so we are going to start the install on the inside of the vehicle and remove some of the interior paneling. 00:31 more
1/28/2011 3:37:33 AM
Trailer Wiring Harness Installation - 2007 Chrysler Town and Country- Video
Today on this 2007 Chrysler Town and Country we are going to install part number 118300 from Tow Ready. First open up the back hatch of the vehicle and disconnect the tail lights. To take off the tail lights what we need to do is pull out these two plastic rivets right here. Swing it out and it pops right out. To disconnect the wire harness we have to push in this red tab right here so it unlocks. Push down at the top of the wire harness and it should come right apart. Repeat the same process on the passenger side. Next we are going to pull out this grommet right here and we are going to make a slit in it so we can run our new harness back through here. We are going to leave it like that for now. Repeat the same thing on the other side. 00:47 more
3/31/2010 1:33:39 PM
Trailer Wiring Harness Installation - 2008 Chrysler Aspen 118390- Video
Today on this 2008 Chrysler Aspen we will be installing part number 118390 from Tow Ready. This is a T-One wiring connector. To begin our install we need to open up the hatch to get to the plastic rivets that holds the tail lights in place. The tail lights have to come off because our wiring connections are behind the tail light themselves. more
9/24/2009 10:16:59 AM
Trailer Wiring Harness Installation - 2003 Chrysler Town and Country- Video
Today on this 2003 Chrysler Town and Country we are going to install 118376 from Tow Ready. Our connection point is actually behind the taillight on the driver side. We are going to go ahead and take out these two plastic rivets, make our connections, then run our 4-pull to the inside of the vehicle, and it will be stored in the jack storage compartment when we are not using it. more
8/31/2009 7:00:11 AM
Trailer Wiring Harness Installation - 2007 Chrysler Pacifica- Video
Today we are going to be installing wiring harness part number 118303 on a 2007 Chrysler Pacifica. Okay, we are at the rear of the vehicle, and we are going to go ahead and locate the attaching points for our wiring harness. The attaching points are actually located directly behind the tail lights. So the first thing we need to do is go ahead and remove both of those. To do that, we just need to remove the two screws here on the inboard side, and then we will just pull the tail light assembly away. more
4/29/2009 6:14:40 AM
Trailer Wiring Harness Installation - 2007 Chrysler 300C- Video
Today we are going to install part number 28406 from Tow Ready. We are going to install this on a 2007 Chrysler 300C. The first step we have to do is get into a trunk area. Then we need to take off these wing nuts to take out this carpeting and expose the wiring that we need to get to. We need to do that on both sides. There is a little plastic fastener that would help for it to come apart too. There is the wiring we need to get to right there. Now pull back this trunk panel right here, exposing the battery and spare tire. Then we will take the wing nut on the other side and get to the wiring there too. Lastly we are going to take off this interior panel right here. Starting on our driver side, we will go ahead and disconnect here and install our T-connector. Simply push this red button out the way, press on the end, and it comes right apart. more
8/7/2008 10:52:02 PM
Filter Videos
Filter Videos
